GSMTRICK
You are not logged in or you do not have permission to access this page. This could be due to one of several reasons:
(1)You are not logged in. Fill in the form at the bottom of this page and try again.
(2)You may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
(3)If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation


BIG COLLECTION OF MOBILE PHONE
 
NEW UPDATEHomeFAQSearchRegisterMemberlistUsergroupsLog in

Share | 
 

 Manual For Repairing Chinesse MTK Phones with ET-BoX

Go down 
AuthorMessage
....::::Munaf::::....
Admin


Number of posts : 409
Age : 34
Location : Ahmedabad.Gujrat.india
Points : 453
Registration date : 2008-01-10

PostSubject: Manual For Repairing Chinesse MTK Phones with ET-BoX   Thu May 28, 2009 6:25 am

ET-BoX Chinesse MTK Beta Manual

  • Read / Write Full Backup
  • Repair Restart Problem
  • Repair Hang Problem
  • Reset Phone Code
  • Repair Dead Phones
  • Repair IMEI
Instructions:



Step-By-Step Manual on how to repair Restart problem, Hanging problem & Reset phone code in chinese phones.

1. Check if phone is supported by ET-BoX or not.

Open the phone and see which CPU does your chinese phone have. If it
has MTK processor (written "M" or "MT" on CPU) then it is supported by
ET-BoX.



2. Connect Cable to ET-BoX

2.1 If you have Cable for this model then simply connect to phone and ET-BoX, if not:
2.2 Open the phone and look if phone board has written somewhere "Rx"
& "Tx". If yes, then connect Rx and Tx to respective wires and
connect GND from ET-BoX to anywhere on shielding.


2.3 If phone board does not have any details written about "Rx" &
"Tx", then look in pinouts section or Support forum for pinouts or PCB
Connection diagrams.



3. Connect Phone to ET-BoX Software

3.1 Open Latest Version of ET-BoX and select the assigned comm port & speed. Then press "Connect Port".


3.2 Power of the phone, remove and then insert battery to it.
3.3 Press "Connect Phone" and then press "Power ON" button on the chinese phone.
3.4 Phone will connect and important information will be displayed on screen about CPU, Flash, Software Version, etc.
Back to top Go down
View user profile http://gsmtrick.forumotion.com
....::::Munaf::::....
Admin


Number of posts : 409
Age : 34
Location : Ahmedabad.Gujrat.india
Points : 453
Registration date : 2008-01-10

PostSubject: Manual For Repairing Chinesse MTK Phones with ET-BoX V2   Thu May 28, 2009 6:26 am

4. Most Important: Read Full Backup of Phone

4.1 Select the "Reader" tab, select "Full Flash", press "Read Flash".


4.2 A dialog box will appear which will ask you the desired path and filename to save backup to. Click "Save".


4.3 ET-BoX will read and save full backup of your phone which can be used in any later stage.





5. Format The Phone

5.1 Select the "Unlocker" tab, tick "Auto Check EEPROM" & then press "Format FFS".


5.2 If step 5.1 gives any error like "Seeking EEPROM error", then
un-tick the "Auto Check EEPROM" and then try "Format FFS" again.



6. Power on the Phone

6.1 After Format is complete, press "Disconnect Phone", Remove cable from phone, remove & insert the battery.


6.2 Press "Power ON" button for longer time than normal (like 30-60 seconds).
6.3 Phone will power on and may ask for one-time setup or screen caliberation.



7. Fix IMEI

7.1 Connect cable to phone and ET-BoX and press "READ IMEI".


7.2 Tick the "Fix IMEI" tab and enter the original IMEI of the phone from the back panel.
7.3 After that press "WRITE IMEI".


7.4 Disconnect phone & Power Off



8. Your Phone is fixed and ready to be used.





Step-By-Step Instructions on how to Flash the Phone with saved backup of the flash.

1. Open Latest Version of ET-BoX and select the assigned comm port & speed. Then press "Connect Port"
2. Power of the phone, remove and then insert battery to it.
3. Press "Connect Phone" and then press "Power ON" button on the chinese phone.
4. Phone will connect and important information will be displayed on screen about CPU, Flash, Software Version, etc.
5. Select the "Flasher" tab & make sure that no file is allready
selected in the Flasher window, if it does then select it and press
"Remove Files". Press "Add Files". A dialog box will appear which will
ask you the path and filename of the backup flash file. Select your
saved backup file and press "Open". Click "Write Files" & ET-BoX
will start writting full backup of your phone.
6. After Flashing is done remove cable from phone and re-insert the battery.




Tips:

# Never ever Flash Phone with any file other than its own backup file.
# If the phone is restarting even without sim card inside, then mostly its a hardware problem.
# If phone is not connecting or giving any sort or compatibility error,
then please make screenshot, read full flash and send it to support@et-box.net
# As Clearly Said Above this is a Beta edition and may cause damages to your phone. So Please use at your own risk.



Br.
ET-BoX Team
www.et-box.net
Back to top Go down
View user profile http://gsmtrick.forumotion.com
 
Manual For Repairing Chinesse MTK Phones with ET-BoX
Back to top 
Page 1 of 1
 Similar topics
-
» Andrew James 12litre
» I need some help repairing and painting some wheels
» cookshop 7685 halogen oven manual pdf
» Need a manual for Heathkit SG-8 sig gen
» Webster-Chicago model 56 manual - FOUND

Permissions in this forum:You cannot reply to topics in this forum
GSMTRICK :: SOFTWARE DEVICE SUPPORT :: ET-BoX-
Jump to: